Water got into the charging socket of my phone. What should I do?

First response to liquid contact on the phone is always useful. Many users who have operated their devices after liquid contact have experienced hardware failure in their devices.

Muhammad Hamza
Writer Muhammad Hamza 11 Minimum Reading
7 First aid in case of liquid contact
What should be done in case of liquid contact?

The problem of water leaking into the charging socket of the phone is encountered by more or less device users. Liquid contact often causes hardware failure. Our article was prepared to answer the question of what to do when there is liquid contact with the phone socket.

Sponsored Ad
Ad imageAd image

The most common mistake in complaints about water leaking into the charging socket of the phone is that the device is turned on after contact with liquid. Opening the device in a liquid state will most likely cause hardware failure. Situations that are not rare may occur.

The first thing you will do in case of liquid contact is as follows:

If the phone is on, turn it off.

  • If the battery is removable, remove it quickly without waiting.
  • Try to dry your device. If you have the knowledge and ability to open the inside of the device, open it and dry it.
  • If you are unaware of the issue, turn off the phone and remove its battery. Then take your device to a technical service.

Water Got into the Charging Socket of the Phone Solution Steps

If you have accidentally spilled or dropped your phone into water, you are faced with a situation that can happen to most of us. To deal with such situations, you can follow the steps below:

  1. Turn Off Your Phone Immediately: First of all, you should turn off your phone. Water can damage the components inside, so it's important to turn off the phone immediately.
  2. Clean Water: If your phone has been dropped into salty water such as seawater or has dirty material inside, rinse your phone quickly with clean water. Then dry gently.
  3. Remove Battery and Cards (If Possible): If you can, remove your phone's battery and SIM card. This may prevent better penetration of water into the internal components.
  4. Do Not Turn On or Charge the Phone: Even if your phone is water resistant, water can enter it and damage the internal components. So do not turn on or charge your phone.
  5. Remove Case and Removable Components: If your phone has a case or accessory on it, remove it. Then use a SIM ejector to remove your phone's SIM card tray. If you have an older model phone and it has a removable battery, remove the batteries as well.
  6. Drying Process: Telefonunuzu açmadan önce, suyun içerideki her yeri kurumasını bekleyin. Telefonunuzu düz bir yüzeye koyun ve havadar bir yerde kurumaya bırakın. Bir pirinç kap içine koymak yerine, silika jel gibi su emici malzemeler kullanmak daha etkili olabilir. Telefonunuzun içindeki suyun kurumasına yardımcı olmak için, telefonu düz bir yüzeye koyun ve havadar bir yerde bırakın. Pirinç gibi su emici bir malzeme kullanmak yerine, telefonun içindeki suyun buharlaşmasını sağlamak daha etkili olacaktır. Telefonunuzun içindeki suyun tamamen buharlaşması 24 ila 48 saat veya daha uzun sürebilir.
  7. Wipe Off Excess Water: If there are still water droplets on your phone's screen or back panel, use a microfiber cloth to clean them. You can gently shake your phone to remove any excess water that may collect in the small openings inside the phone.
  8. Check IP Rating: Check your phone's IP rating to determine its water resistance level. Phones that can be submerged in water for a certain period of time may be IP67 or IP68 certified. If they have these certifications, they are better protected against water.
  9. Expert Assistance: If your phone still does not work or the problems persist, you may need to contact a phone repair service or the manufacturer.
Water got into the charging socket of the phone 1
Water got into the charging socket of the phone problem

Dry the Device Outdoors

The best and safest way to remove water from inside your phone is to let it air dry. You can follow the steps below:

Sponsored Ad
Ad imageAd image
  1. Leave the Phone Bare: First, remove your phone's case or any covering. This will help the water evaporate faster.
  2. Place the Charging Port Facing Down: Place your phone on a flat surface and place the charging port facing down. This allows water to flow out of the charging port and allow gravity to do its work.
  3. Allow Natural Air Circulation: Make sure you keep your phone in a place with natural air circulation. It should be outdoors or near a window, not in a closed environment.
  4. Dry the Phone for Appropriate Time: It may take a few hours to a few days for the water on your phone to completely evaporate. Depending on the amount of water, I recommend drying the phone for at least 24 hours.
  5. If You Want to Speed ​​Up the Process: You can use a fan or air conditioner to speed up the drying process. However, be careful not to use hot air when using the air conditioner as this may damage the components inside your phone. It is safer to use cold air.

Using a Vacuum Cleaner to Fix Water Leaking in the Charging Socket of the Phone

If your phone is completely submerged in water and you want to quickly remove excess water, you have the option of using a shop vacuum or vacuum cleaner. Here are the edits to explain this process in more detail:

  1. Prepare the Shop Vac or Vacuum Cleaner: Properly prepare a shop broom or vacuum cleaner. If possible, use gentle suction mode, as too strong suction may damage internal components.
  2. Apply to Your Phone's Openings: Bring the suction tube closer to all openings of your phone (charging port, speaker, microphone, headphone jack, etc.). Suction for approximately 10-15 seconds for each opening.
  3. Be careful: Be careful when sucking into your phone and avoid applying pressure. Also, be careful not to place the suction tube too closely to avoid damaging internal components.
  4. Repeat Sweeping: Repeat the vacuuming process several times to remove excess water from inside the phone. Move the suction tube to each opening of the phone before turning off the cleaner.
  5. Dry Your Phone Outdoors: If you have now absorbed most of the excess water, leave your phone to dry naturally outdoors. It's a good idea to leave the phone for at least 24 hours until more water evaporates.

Using Silica Gel Packs to Fix Water Leaking in the Charging Socket of the Phone

Using hygroscopic materials like Silica Gel Packs to dry your phone is also an effective method. Silica Gel has a moisture absorbing feature and helps water evaporate. Here are the edits to explain this method in more detail:

  1. Prepare Silica Gel Packs: Obtain Silica Gel Packs. These packages usually come with new shoes, bags or electronics. If you do not have these packages, you can buy them in pharmacies or online stores.
  2. Pack Your Phone with Silica Gel: Place your phone in a bag or box. Then put the Silica Gel Packs around the phone. Ensure the phone is completely covered and if possible place Silica Gel Packs inside the phone as well.
  3. Store in a Closed Environment: After packing your phone with Silica Gel, seal this bag or box tightly. This helps Silica Gel be more effective. Keep your phone in this closed environment.
  4. Wait Patiently: It may take a few days for the water on your phone to completely evaporate. So be patient and leave your phone packed in Silica Gel for at least 48 hours.
  5. Check It Out and Get Started: Once the water inside your phone has finished evaporating, check your phone and make sure everything is working properly. Then you can start using your phone.
Water got into the charging socket of the phone 2
Water got into the charging socket of the phone

How do we know if the phone is completely dry?

You can take some observations and precautions to understand that your phone is completely dry. Especially for iPhone and Android devices, you can follow the steps below:

  1. Pay Attention to the Signs: If you get the “Liquid Detected in Lightning Connector” error when you connect a cable to your iPhone's Lightning port, your phone may still be wet. If you don't see this error, your phone is probably dry.
  2. Heating and Shiver Control: A wet phone may often overheat or show abnormalities such as minor errors, screen flickering, etc. If you do not experience problems such as overheating or unexpected flickering when using your phone, the drying process may have been successful.
  3. Watch for Touch Issues: Wet phones can sometimes experience ghost touches or shifts in touch sensitivity. If your touch screen works normally, it may indicate that the water inside your phone has evaporated.
  4. Speaker and Volume Control: Water damage can cause problems with speakers and affect sound quality. If your phone's speakers are producing normal sound and the sound is not muffled, the drying process may be complete.
  5. Make Sure the Phone is Working Well: In general, make sure your phone is working normally. If everything is fine and you are not experiencing any problems, you can say that your phone is completely dry.

Note: Residues from contact with sticky liquids such as juice may remain on the screen or charging port after drying. To remove such debris, you can follow the cleaning instructions recommended by your phone's manufacturer.

Things to Consider When Removing Water from the Charging Port

Here are the mistakes to avoid and points to pay attention to when trying to remove water from your phone's charging port:

  1. Don't Let Your Phone Dry Out: If your phone has poor water resistance, it may be best to let it dry naturally. Leaving it in water for a long time may cause corrosion and damage to the electronic components inside.
  2. Avoid Drying in the Sun: Do not leave your phone to dry under the sun. The metal and glass surfaces of the phone absorb heat quickly, which can cause your phone to overheat and cause further damage. Drying in a naturally ventilated area is preferred.
  3. Avoid Using Rice: Rice can absorb moisture from its surroundings, but small grains of rice can get stuck in your phone's openings or ports. This can cause problems that are difficult to clean up.
  4. Do Not Use a Cotton Swab to Wipe the Charging Port: Avoid using cotton swabs, tissues, or cloth to wipe the charging port. These materials can leave residue such as lint and fibers and get wet. They can also cause damage to delicate pins.
  5. Avoid Shaking the Phone: Shaking or shaking your phone when you take it out of water may cause some water to move into the phone. Therefore, avoid shaking your phone.
  6. Do Not Use a Hair Dryer or Compressed Air: Using a hair dryer, compressed air, or similar tools can push water droplets further into your phone, and high temperature can damage components inside your phone.

Remember that it is important to be careful with phones exposed to water as the damage can be difficult to pinpoint and repair. Therefore, try to ensure that your phone is optimally protected by following the steps above.

We explained step by step what to do to solve the problem of water getting into the charging socket of the phone.

Next:iPhone not charging

What should be done in case of liquid contact?
First aid in case of liquid contact 7
First response steps to liquid contact 8
Necessary cleaning steps in case of liquid contact 6
He is someone who has worked on both technology and articles for many years. He also researches the technological problems he encounters from time to time and prepares solution content for them.
Leave a review

Leave a review

Your email address will not be published. Required fields*They are marked with